Rite-ride 8619 Manuel d'utilisateur télécharger pdf

08-09 NBD-16766-1

WORK-RITE LOAD ASSISTS 1260 2

LEFT UPPER BRACKET 5635 1

RIGHT UPPER BRACKET 5636 1

SLEEVE 5224 2

3/8"-16 X 1" HEX BOLT 2

PARTS LIST

8619

INSTALLATION INSTRUCTIONS

Congratulations – your new Work-Rite load assists are quality products

capable of improving the handling and comfort of your vehicle while under load. As

with all products, proper installation is the key to obtaining all of the benefits your

kit is capable of delivering. Please take a few minutes to read through the

instructions to identify the components and learn where and how they are used. It

is a good idea to start by comparing the parts in your kit with the parts list below.

NOTE: IF ANY PARTS ARE MISSING FROM THE KIT,

PLEASE CALL 1-800-888-0650.

PLEASE DO NOT CALL OR RETURN THE KIT TO THE DEALER.

Be sure to take all applicable safety precautions during the installation of the

kit. The instructions listed in this brochure and the illustrations all show the left,

or driver’s side of the vehicle. To install the right side assembly simple follow the

same procedures.

STEP 1 – PREPARE THE VEHICLE

With the vehicle on a solid, level surface chock the front wheels. Remove the

negative battery cable. Remove the jounce bumpers located under the frame rail.

The jounce bumpers, bolts, and nuts will not be re-used with this kit.

STEP 2 – PRE-ASSEMBLE THE KIT

Select the left upper bracket (5635) and insert a 3/8"-16 x 1-1/2" carriage bolt

into the square hole. See Figure “A”. Select one Work-Rite load assist from your

kit and attach it to the upper bracket using a 3/8"-16 x 1" hex head bolt and flat

washer inserted through the bottom of the Work-Rite and into the small hole in the

top, then secure to the upper bracket using a 3/8"-16 flange lock nut. See Figure

“A”.

STEP 3 – INSTALLING THE ASSEMBLY ON THE VEHICLE

Place the sleeve over the carriage bolt installed in Step 2. Attach the upper

bracket onto the vehicle by inserting the 3/8"-16 x 1-1/2” carriage bolt into the

slotted hole on the jounce bumper brace. NOTE: The tab on the upper bracket will

also insert into the slotted hole on the jounce bumper brace. See Figure "A".

Install a 3/8"-16 flange lock nut and washer onto the carriage bolt and tighten. A

ratcheting box wrench would make this easier to install. See Figure “A”.

Repeat steps 1-3 for the right side of the vehicle.

STEP 4 – FINISH UP

Remove the wheel chocks and reconnect the battery cable. Now you're finished

and ready to put your Work-Rite to use!

3/8"-16 X 1-1/2" CARRIAGE BOLT 2

3/8"-16 FLANGE LOCK NUT 4

3/8" FLAT WASHERS 2

3/8" LARGE FLAT WASHERS 2

1 2 3 4

Résumé du contenu

Page 1

08-09 NBD-16766-1WORK-RITE LOAD ASSISTS 1260 2LEFT UPPER BRACKET 5635 1RIGHT UPPER BRACKET 5636 1SLEEVE 5224 23/8"-16 X 1" HEX BOLT 2PARTS

Page 2 - FIGURE "A"

WORK-RITE3/8” -16 x 1-1/2”HEX HEAD BOLT & 3/8” FLAT WASHER3/8”-16 X 1-1/2”CARRIAGE BOLTUPPERBRACKET3/8”-16FLANGE LOCK NUTSLEEVEJOUNCE BUMPERBRACEF

Page 3 - Do Not Return This Product

Do Not Return This Product to the Dealer or DistributorIf you are• missingparts,• experiencinginstallationproblems,or• havetechnicalconcerns

Page 4

FIRESTONE LIMITED LIFETIME AIR SPRING WARRANTYFirestone Industrial Products Company LLC (“Firestone”) warrants that its Ride Rite Air Spring Assembly

Commentaires sur ces manuels

Pas de commentaire

Rite-ride 8619 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Rite-ride 8619. Rite-Ride 8619 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Rite-ride 8619