Rite-ride 2255 Manuel d'utilisateur télécharger pdf

2255

PARTS LIST

INSTALLATION INSTRUCTIONS

Congratulations - your new Air Helper Springs are quality

products capable of improving the handling and comfort of

your vehicle. As with all products, proper installation is the

key to obtaining all of the benefits your kit is capable of

delivering. Please take a few minutes to read through the

instructions to identify the components and learn where and

how they are used. It is a good idea to start by comparing the

parts in your kit with the parts list below.

The heart of the air spring kit is, of course, the air helper

springs. Remember that the air helper springs must flex and

expand during operation, so be sure that there is enough

clearance to do so without rubbing against any other part of

the vehicle.

Be sure to take all applicable safety precautions during the

installation of the kit. The instructions listed in this brochure

and the illustrations all show the left, or driver’s side of the

vehicle. To install the right side assembly simply follow the

same procedures.

Your kit includes separate inflation valves and air lines for

each air helper spring. This will allow you to level your vehicle

from side to side as well as from front to back. If you would

rather have a single valve inflation system, your dealer can

supply the required "T" fitting.

IMPORTANT!

For your safety and to prevent possible damage to your

vehicle, do not exceed the maximum load recommended by

the vehicle manufacturer (GVWR). Although your Air Helper

Springs are rated at a maximum inflation pressure of 100

psi, this pressure may allow you to carry too great a load

on some vehicles. It is best to have your vehicle weighed

once it is completely loaded and compare that weight to

the maximum allowed. Check your vehicle owner’s manual

or data plate on driver side door for maximum loads

listed for your vehicle.

When inflating your Air Helper Springs, add air pressure

in small quantities, checking pressure frequently during

inflation. The air spring requires much less air volume than

a tire and, therefore, inflates much quicker.

TOOLS REQUIRED

• (2) 9/16" END WRENCHES • ELECTRIC DRILL

• (2) 1/2" END WRENCHES • 5/16" DRILL BIT

• UTILITY KNIFE

AIR SPRING 6781 2

UPPER BRACKET 5302 2

LOWER BRACKET 5307 2

BRACKET STRAP 1163 2

BAIL CLAMP 3077 2

18 ft. TUBING 0938 1

PUSH-TO-CONNECT

INFLATION VALVE 3032 2

1/4 NPT STRAIGHT FITTING 3046 2

THERMAL SLEEVE 0899 2

21-8227 09-07 NAD-31157-3

3/8"-16 X 1-1/2" HEX BOLT 4

3/8"-16 FLANGE LOCK NUT 18

3/8"-16 X 3/4" FLANGE BOLT 2

3/8"-16 X 3" CARRIAGE BOLT 4

3/8"-16 X 1-1/2" CARRIAGE BOLT 2

3/8" FLAT WASHER 3

5/16" FLAT WASHER 4

NYLON TIE WRAP 6

CAUTION TAG 2

WARNING:

Do not inflate this assembly when it is

unrestricted. The assembly must be restricted by

the suspension or other adequate structure. Once

installed, do not inflate beyond 100 psi. Improper

use or over inflation may cause property damage

or severe personal injury.

1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1 - WARNING:

2255PARTS LISTINSTALLATION INSTRUCTIONSCongratulations - your new Air Helper Springs are qualityproducts capable of improving the handling and comfort

Page 2 - ON LEFT SIDE ONLY

6TROUBLE SHOOTING GUIDEAir spring will not inflateEnsure that the air line tubing is inserted into the air fittings as far as possible. The tubing s

Page 3 - TEP 2 - PRE-ASSEMBLE THE KIT

7FIRESTONE LIMITED LIFETIME AIR SPRING WARRANTYFirestone Industrial Products Company LLC (“Firestone”) warrants that its Ride Rite Air Spring Assembly

Page 4 - MAX PRESSURE (LOADED) 100 PSI

Page 5 - Trouble Shooting Guide

LKITASSEMBLYNOTE: Both illustrations are of the left, or driversside of the vehicle. Reverse any orientations wheninstalling the right, or passeng

Page 6

Figure "E"Figure "B"Figure "D"STEP 1 - PREPARE THE VEHICLEPlace the vehicle on a solid level surface. Remove negative b

Page 7

NOTE:Once the air helper springs are installed, it is recommended that the vehicle not be lifted by the frame, as over-extensionmay occur, result

Page 8 - ONLINE AUCTION PURCHASES

Operating Instructions and Trouble Shooting Guide21-1083 4-12 Thank you for purchasing Firestone air helper springs. You have purchased a quality prod

Page 9 - AIR SPRING TECHNICAL DATA

2SAFETY TIPSNever exceed the manufacturer’s recommended Gross Vehicle Weight Rating (GVWR)As with your vehicle’s tires, an air helper spring is a pneu

Page 10 - IMPORTANT

3the suspension system. As more air pressure is added to the air springs, they will support more weight. You will be able to compensate for a heavy lo

Page 11 - WARRANTY QUESTIONS

4INFLATING THE AIR SPRINGSWith the air helper springs installed on your vehicle and the vehicle sitting on a level surface, visually verify that the v

Page 12 - STEP: #1:

5Description Style Ride Height“X”Min/Max AirPressureMax Load @100 psi(per pair)6868 Single Convoluted 160BY 5.0" - 6.0" 5 / 100 psi 3600 lbs

Commentaires sur ces manuels

Pas de commentaire

Rite-ride 2255 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Rite-ride 2255. Rite-Ride 2255 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Rite-ride 2255