Rite-ride 4181 Manuel d'utilisateur télécharger pdf

AIR

INLET

BLUNT TOOL

PLUG

AIR LINE

23-8383 01-12

Read installation instructions completely before installing your Coil-Rite Kit

RECOMMENDED OPERATING PRESSURES

PASSENGER CARS & SUV'S 5-25 p.s.i.

Installation Instructions

VEHICLE PREPARATION

With the vehicle on a solid level surface chock the

wheels and raise the vehicle using a jack rated for your

vehicle weight to lift the wheels off the surface. Remove

the wheels. Lower the vehicle frame onto jack stands

rated for your vehicles weight making sure the suspen-

sion is fully extended. (Do NOT use wood or concrete

blocks to support the weight of the vehicle.) Next, drill

a 1/2" hole into the bottom of the spring seat for the air

line to pass through.

SHOCK ABSORBERS

If necessary, additional clearance between the coil

turns may be obtained by removing the shock absorb-

ers from the lower shock mounts and lowering the sus-

pension an additional one to two inches. (CAUTION:

Do not put strain or tension on the ﬂexible brake line.)

STEP 1 AIR SPRING PREPARATION

Cut a section of air line tubing approximately three

inches in length. (Cut the tubing as squarely as possi-

ble.) Install the tubing into the push-to-connect air inlet

on the air spring. Exhaust the air from the air spring

by rolling it up toward the air inlet. After all the air is

removed from the air spring install the hose plug into

the end of the hose as shown in Figure “A”.

STEP 2 INSTALLING THE AIR SPRING

Insert the top of the ﬂattened air spring into the coil

spring through the lowest opening with the push-to-

connect air inlet at the bottom as shown in Figure “A”.

STEP 3 ADJUSTING THE AIR SPRING

Push the air spring up into the coil spring by hand or

with a blunt tool, such as a spoon shaped tire iron. Do

NOT use anything with sharp edges or corners as this

may damage the air spring.

WARNING

Do not inﬂate this assembly when it is

unrestricted. The assembly must be restricted

by a coil spring. Do not ever inﬂate beyond

recommended operating pressures for your

speciﬁc vehicle. Improper use or over inﬂation

may cause property damage or severe

personal injury.

When the air spring is completely within the coil

spring, remove the plug and three inch tubing sec-

tion by pushing the collar on the ﬁtting towards the air

spring and pulling on the tubing to remove. Allow the

air spring to return to its normal shape. Push the air

spring to the bottom of the coil spring. Insert one of the

supports between the air spring and the upper spring

seat. See Figure “B”.

STEP 4 REATTACH THE SHOCK ABSORBER

Attach shock absorbers if removed earlier in the instal-

lation.

Figure “A”

4181

1 2 3 4

Résumé du contenu

Page 1 - Installation Instructions

AIRINLETBLUNT TOOLPLUGAIR LINE23-8383 01-12 Read installation instructions completely before installing your Coil-Rite KitRECOMMENDED OPERATING PRE

Page 2 - AIR LINE INSTALLATION

AIR LINE INSTALLATIONFigure “C”PLEASE TAKE ALL NECESSARY SAFETY PRECAUTIONS WHEN INSTALLING YOUR COIL-RITE KIT.STEP 5 ROUTE THE AIR LINECut the remai

Page 3 - Do Not Return This Product

Do Not Return This Product to the Dealer or DistributorIf you are• missingparts,• experiencinginstallationproblems,or• havetechnicalconcerns

Page 4

FIRESTONE LIMITED LIFETIME AIR SPRING WARRANTYFirestone Industrial Products Company LLC (“Firestone”) warrants that its Ride Rite Air Spring Assembly

Commentaires sur ces manuels

Pas de commentaire

Rite-ride 4181 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Rite-ride 4181. Rite-Ride 4181 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Rite-ride 4181