Rite-ride 8610 Manuel d'utilisateur télécharger pdf

02-09 NAD-37104

WORK-RITE LOAD ASSISTS 1260 2

UPPER BRACKET (4X2 KIT) 5608 2

UPPER BRACKET (4X4 KIT) 5621 2

OPTIONAL SPACERS 0013 4

3/8"-16 X 1" HEX BOLT 2

PARTS LIST

8609 / 8610

INSTALLATION INSTRUCTIONS

Congratulations – your new Work-Rite load assists are quality products

capable of improving the handling and comfort of your vehicle while under load. As

with all products, proper installation is the key to obtaining all of the benefits your

kit is capable of delivering. Please take a few minutes to read through the

instructions to identify the components and learn where and how they are used. It

is a good idea to start by comparing the parts in your kit with the parts list below.

NOTE: IF ANY PARTS ARE MISSING FROM THE KIT,

PLEASE CALL 1-800-888-0650.

PLEASE DO NOT CALL OR RETURN THE KIT TO THE DEALER.

Be sure to take all applicable safety precautions during the installation of the

kit. The instructions listed in this brochure and the illustrations all show the left,

or driver’s side of the vehicle. To install the right side assembly simple follow the

same procedures.

STEP 1 – PREPARE THE VEHICLE

With the vehicle on a solid, level surface chock the front wheels. Remove the

negative battery cable. Remove the jounce bumpers located under the frame rail.

The jounce bumpers, bolts, and nuts will not be re-used with this kit.

STEP 2 – PRE-ASSEMBLE THE KIT

Select one Work-Rite load assist from your kit. Insert a 3/8"-16 x 1" bolt and

flat washer through the bottom of the Work-Rite and into the small hole in the top.

Fasten the Work-Rite to the upper bracket using a flange lock nut. See Figure “A”.

NOTE: An optional spacer may be installed to engage the Work-Rite sooner

when a load is applied. To install, place between the Work-Rite and the upper

bracket. If the spacers are installed, use the 3/8"-16 x 2" bolts instaed of the

3/8"-16 x 1" bolts. There should be 1/4" to 3/8" between the Work-Rite and

the axle. See Figure "B".

STEP 3 – INSTALLING THE ASSEMBLY ON THE VEHICLE

Attach the upper bracket onto the vehicle using 3/8"-16 x 1-1/2” hex bolts,

large flat washers, and flange lock nuts inserted into the holes from the jounce

bumper. The long leg of the upper bracket should be facing to the front of the vehicle.

See Figure “A”.

STEP 4 – FINISH UP

Remove the wheel chocks and reconnect the battery cable. Now you're finished

and ready to put your Work-Rite to use!

3/8"-16 X 2" HEX BOLT 2

3/8"-16 X 1-1/2" HEX BOLT 4

3/8"-16 FLANGE LOCK NUT 6

3/8" FLAT WASHERS 2

3/8" LARGE FLAT WASHERS 4

1 2 3 4

Résumé du contenu

Page 1

02-09 NAD-37104WORK-RITE LOAD ASSISTS 1260 2UPPER BRACKET (4X2 KIT) 5608 2UPPER BRACKET (4X4 KIT) 5621 2OPTIONAL SPACERS 0013 43/8"-16 X 1"

Page 2 - Figure "B"

*OPTIONAL SPACERS*CAN BE USED TO ENGAGEWORK-RITE SOONER3/8”-16X1”HEX BOLT& FLAT WASHERORUSE 2” BOLT IFADDING SPACERSFigure "A"1/4”-3/8”W

Page 3 - Do Not Return This Product

Do Not Return This Product to the Dealer or DistributorIf you are• missingparts,• experiencinginstallationproblems,or• havetechnicalconcerns

Page 4

FIRESTONE LIMITED LIFETIME AIR SPRING WARRANTYFirestone Industrial Products Company LLC (“Firestone”) warrants that its Ride Rite Air Spring Assembly

Modèles reliés 8609

Commentaires sur ces manuels

Pas de commentaire

Rite-ride 8610 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Rite-ride 8610. Rite-Ride 8610 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 8609

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Rite-ride 8610