Rite-ride 2251 Manuel d'utilisateur télécharger pdf

2251

PARTS LIST

INSTALLATION INSTRUCTIONS

Congratulations — your new Air Helper Springs are quality

products capable of improving the handling and comfort

of your vehicle. As with all products, proper installation is

the key to obtaining all of the beneﬁts your kit is capable

of delivering. Please take a few minutes to read through

the instructions to identify the components and learn

where and how they are used. It is a good idea to start by

comparing the parts in your kit with the parts list below.

The heart of the air spring kit is, of course, the air

helper springs. Remember that the air helper springs must

ﬂex and expand during operation, so be sure that there

is enough clearance to do so without rubbing against

any other part of the vehicle.

Be sure to take all applicable safety precautions

during the installation of the kit. The instructions listed

in this brochure and the illustrations all show the left,

or driver’s side of the vehicle. To install the right side

assembly simply follow the same procedures.

Your kit includes separate inﬂation valves and air

lines for each air helper spring. This will allow you to

level your vehicle from side to side as well as from front

to back. If you would rather have a single valve inﬂation

system, your dealer can supply the required “T” ﬁtting.

IMPORTANT!

For your safety and to prevent possible damage

to your vehicle, do not exceed the maximum load

recommended by the vehicle manufacturer (GVWR).

Although your Air Helper Springs are rated at a maximum

inﬂation pressure of 100 psi, this pressure may allow you

to carry too great a load on some vehicles. It is best to

have your vehicle weighed once it is completely loaded

and compare that weight to the maximum allowed. Check

your vehicle owner’s manual or data plate on driver side

door for maximum loads listed for your vehicle.

When inﬂating your Air Helper Springs, add air pres-

sure in small quantities, checking pressure frequently

during inﬂation. The air spring requires much less air

volume than a tire and, therefore, inﬂates much quicker.

TOOLS REQUIRED

(2) 9/16" END WRENCHES ELECTRIC DRILL

(2) 1/2" END WRENCHES 5/16" DRILL BIT

UTILITY KNIFE

AIR SPRING 6781 2

UPPER BRACKET 5302 2

LOWER BRACKET 5304 2

LOWER BRACE 5303 2

BRACKET STRAP 1163 2

BAIL CLAMP 3077 2

18 FT. TUBING 0938 1

PUSH-TO-CONNECT INFLATION VALVE 3032 2

1/4 NPT STRAIGHT FITTING 3046 2

THERMAL SLEEVE 0899 2

21-8225 04-11 NAD-31145-2

3/8"-16 X 1" HEX BOLT 8

3/8"-16 X 1-1/2" HEX BOLT 4

3/8"-16 FLANGE LOCK NUT 26

3/8"-16 X 3/4" HEX BOLT 2

3/8"-16 X 3" CARRIAGE BOLT 4

3/8"-16 X 1-1/2" CARRIAGE BOLT 2

3/8" FLAT WASHER 3

5/16" FLAT WASHER 4

NYLON TIE WRAP 6

CAUTION TAG 2

WARNING:

Do not inflate this assembly when it is

unrestricted. The assembly must be restricted

by the suspension or other adequate structure.

Once installed, do not inﬂate beyond 100 psi.

Improper use or over inﬂation may cause

property damage or severe personal injury.

1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1 - WARNING:

2251PARTS LISTINSTALLATION INSTRUCTIONSCongratulations — your new Air Helper Springs are quality products capable of improving the handling and comfor

Page 2 - FIGURE “A”

6TROUBLE SHOOTING GUIDEAir spring will not inflateEnsure that the air line tubing is inserted into the air fittings as far as possible. The tubing s

Page 3 - Lower bracket assembLy

7FIRESTONE LIMITED LIFETIME AIR SPRING WARRANTYFirestone Industrial Products Company LLC (“Firestone”) warrants that its Ride Rite Air Spring Assembly

Page 4 - STEP 6— CHECK THE AIR SYSTEM

Page 5 - Trouble Shooting Guide

LLLOWER BRACKET3/8"-16 x 3"CARRIAGE BOLTLOWER BRACESEE STEP 23/8"-16HEX NUT3/8”-16HEX NUTSASSEMBLED AIR SPRING KITFRAMEINSTALL THIS WAS

Page 6

STEP 1—PREPARE THE VEHICLEPlace the vehicle on a solid level surface. Remove negative battery cable. Take necessary safety precautions such as using

Page 7

NOTE:Once the air helper springs are installed, it is recommended that the vehicle not be lifted by the frame, as over-extension may occur, resulting

Page 8 - ONLINE AUCTION PURCHASES

Operating Instructions and Trouble Shooting Guide21-1083 4-12 Thank you for purchasing Firestone air helper springs. You have purchased a quality prod

Page 9 - AIR SPRING TECHNICAL DATA

2SAFETY TIPSNever exceed the manufacturer’s recommended Gross Vehicle Weight Rating (GVWR)As with your vehicle’s tires, an air helper spring is a pneu

Page 10 - IMPORTANT

3the suspension system. As more air pressure is added to the air springs, they will support more weight. You will be able to compensate for a heavy lo

Page 11 - WARRANTY QUESTIONS

4INFLATING THE AIR SPRINGSWith the air helper springs installed on your vehicle and the vehicle sitting on a level surface, visually verify that the v

Page 12 - STEP #3:

5Description Style Ride Height“X”Min/Max AirPressureMax Load @100 psi(per pair)6868 Single Convoluted 160BY 5.0" - 6.0" 5 / 100 psi 3600 lbs

Commentaires sur ces manuels

Pas de commentaire

Rite-ride 2251 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Rite-ride 2251. Rite-Ride 2251 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Rite-ride 2251