Rite-ride 2264 Manuel d'utilisateur télécharger pdf

2264

21-8231 11-07 NAD-31350-3

INSTALLATION INSTRUCTIONS

Congratulations - your new Air Helper Springs are quality

products capable of improving the handling and comfort of

your vehicle. As with all products, proper installation is the

key to obtaining all of the benefits your kit is capable of

delivering. Please take a few minutes to read through the

instructions to identify the components and learn where

and how they are used. It is a good idea to start by comparing

the parts in your kit with the parts list below.

The heart of the air helper spring kit is, of course, the air

springs. Remember that the air helper springs must flex and

expand during operation, so be sure that there is enough

clearance to do so without rubbing against any other part of the

vehicle.

Be sure to take all applicable safety precautions during the

installation of the kit. The instructions listed in this brochure

and the illustrations all show the left, or driver’s side of the

vehicle. To install the right side assembly simply follow the

same procedures.

This kit includes inflation valves and air lines for each air

spring. This will allow you to compensate for unbalanced

loads. If you would rather have a single inflation valve system

to provide equal pressure to both air springs, your dealer can

supply the optional "T" fitting.

IMPORTANT!

For your safety and to prevent possible damage to your

vehicle, do not exceed the maximum load recommended by

the vehicle manufacturer (GVWR). Although your Air Helper

Springs are rated at a maximum inflation pressure of 100

P.S.I., this pressure may allow you to carry too great a load

on some vehicles. It is best to have your vehicle weighed

once it is completely loaded and compare that weight to the

maximum allowed. Check your vehicle owner’s manual or

data plate on driver's side door for maximum loads listed

for your vehicle.

When inflating your Air Helper Springs, add air pressure

in small quantities, checking pressure frequently during

inflation. The air spring requires much less air volume

than a tire and, therefore, inflates much quicker.

TOOLS REQUIRED

• (2) 9/16" END WRENCHES • ELECTRIC DRILL

• (2) 1/2" END WRENCHES • 5/16" DRILL BIT

• UTILITY KNIFE • 3/8" DRILL BIT

WARNING:

Do not inflate this assembly when it is unrestricted.

The assembly must be restricted by the suspension or

other adequate structure. Do not inflate beyond 100

P.S.I. Improper use or over inflation may cause property

damage or severe personal injury.

267C AIR SPRING 6781 2

UPPER BRACKETS 5318 2

LOWER BRACKETS 5092 2

BRACKET STRAP/SHIM 1/2" 5086 4

BRACKET STRAP/SHIM 1" 5093 4

BRAKE LINE BRACKET 1

AIR LINE TUBING 1

3/8"-16 FLANGE LOCK NUT 21

3/8"-16 X 3/4" FLANGE HEX BOLT 2

3/8"-16 X 1" HEX HEAD BOLT 1

3/8"-16 x 7" CARRIAGE BOLTS 8

3/8" FLAT WASHER 12

3/8"-16 X 1 1/2 HEX BOLTS 8

5/16" FLAT WASHER 4

INFLATION VALVE 2

ELBOW FITTING 2

THERMAL SLEEVE 2

NYLON TIE 6

CAUTION TAG 2

PARTS LIST

Installation of this kit requires a minimum of

7-1/2" of clearance between the tire side wall

and the frame.

This kit will not fit the 1997-03 Ford F-150 & 250 light

duty pickups under 8500 GVWR.

1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1 - ARTS LIST

226421-8231 11-07 NAD-31350-3INSTALLATION INSTRUCTIONSCongratulations - your new Air Helper Springs are qualityproducts capable of improving the handl

Page 2 - 7/16"

6TROUBLE SHOOTING GUIDEAir spring will not inflateEnsure that the air line tubing is inserted into the air fittings as far as possible. The tubing s

Page 3 - STEP 2 - PREASSEMBLE THE KIT

7FIRESTONE LIMITED LIFETIME AIR SPRING WARRANTYFirestone Industrial Products Company LLC (“Firestone”) warrants that its Ride Rite Air Spring Assembly

Page 4 - MAX PRESSURE (LOADED) 100 PSI

Page 5 - Trouble Shooting Guide

FRONTWHEELNOTE: Both illustrations are of the left, or driversside, of the vehicle. Reverse any orientations whenassembling and installing the right

Page 6

DRIVER'S SIDEFRONT FIGURE "B" FIGURE "C" FIGURE "D" FIGURE "E"STEP 1 - PREPARE THE VEHICLEWith the ve

Page 7

STEP 4 - INSTALLATION TO THE VEHICLEAfter drilling the holes in the frame rail place the assembled air spring back onthe leaf stack making sure the lo

Page 8 - ONLINE AUCTION PURCHASES

Operating Instructions and Trouble Shooting Guide21-1083 4-12 Thank you for purchasing Firestone air helper springs. You have purchased a quality prod

Page 9 - AIR SPRING TECHNICAL DATA

2SAFETY TIPSNever exceed the manufacturer’s recommended Gross Vehicle Weight Rating (GVWR)As with your vehicle’s tires, an air helper spring is a pneu

Page 10 - IMPORTANT

3the suspension system. As more air pressure is added to the air springs, they will support more weight. You will be able to compensate for a heavy lo

Page 11 - WARRANTY QUESTIONS

4INFLATING THE AIR SPRINGSWith the air helper springs installed on your vehicle and the vehicle sitting on a level surface, visually verify that the v

Page 12 - STEP #2:

5Description Style Ride Height“X”Min/Max AirPressureMax Load @100 psi(per pair)6868 Single Convoluted 160BY 5.0" - 6.0" 5 / 100 psi 3600 lbs

Commentaires sur ces manuels

Pas de commentaire

Rite-ride 2264 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Rite-ride 2264. Rite-Ride 2264 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Rite-ride 2264