Rite-ride 2378 Manuel d'utilisateur télécharger pdf

2378

NSTALLATION I NSTRUCTIONS

Congratulations - your new Air Helper Springs are

quality products capable of improving the handling and

comfort of your vehicle. As with all products, proper

installation is the key to obtaining all of the benefits your

kit is capable of delivering. Please take a few minutes to

read through the instructions to identify the components

and learn where and how they are used. It is a good idea

to start by comparing the parts in your kit with the parts

list below.

The heart of the kit is, of course, the air springs.

Remember that the air springs must flex and expand

during operation, so be sure that there is enough clearance

to do so without rubbing against any other part of the

vehicle.

Be sure to take all applicable safety precautions during

the installation of the kit. The instructions listed in this

brochure and the illustrations all show the left side of the

vehicle. To install the right side assembly simply follow the

same procedures.

This kit includes inflation valves and air lines for each

air spring. This will allow you to compensate for unbal-

anced loads. If you would rather have a single inflation

valve system to provide equal pressure to both air springs,

your dealer can supply the optional "T" fitting.

IMPORTANT!

For your safety and to prevent possible damage to

your vehicle, do not exceed the maximum load

recommended by the vehicle manufacturer (GVWR).

Although your Air Helper Springs are rated at a maximum

inflation pressure of 100 psi, this pressure may allow you

to carry too great a load on some vehicles. Check your

vehicle owner’s manual or manufacture plate on

driver side door for maximum loads listed for your

vehicle.

When inflating your Air Helper Springs, add air

pressure in small quantities, checking pressure fre-

quently during inflation. The air spring requires much

less air volume than a tire and, therefore, inflates much

quicker.

21-8308 10-07 NAD-34381-4

WARNING:

Do not inflate this assembly when it is

unrestricted. The assembly must be restricted by

the suspension or other adequate structure. Do

not inflate beyond 100 psi Improper use or over

inflation may cause property damage or severe

personal injury.

PARTS LIST

AIR SPRINGS 9000 2

UPPER BRACKETS 5377 2

LOWER BRACKETS 5489 2

DISK 5260 2

BRACKET STRAPS 5086 2

AIR LINE TUBING 1

3/8"-16 X 4" HEX BOLTS 8

3/8"-16 FLANGE LOCK NUTS 12

3/8"-16 X 3/4" FLANGE HEX BOLTS 6

3/8"-16 X 4.5" CARRIAGE BOLTS 4

3/8" SPECIAL FLAT WASHERS 8

5/16" FLAT WASHERS 4

PUSH TO CONNECT

INFLATION VALVES 3098 2

VALVE CAPS 2

PUSH TO CONNECT

ELBOW FITTINGS 3101 2

NYLON TIES 6

THERMAL SLEEVES 2

CAUTION TAG 2

Installation of this kit requires a

minimum of 6" of clearance between the

tire side wall and the vehicle frame and a

1/2" of clearance around the air spring

when inflated.

1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1 - PARTS LIST

2378INSTALLATION I NSTRUCTIONSCongratulations - your new Air Helper Springs arequality products capable of improving the handling andcomfort of your v

Page 2

6TROUBLE SHOOTING GUIDEAir spring will not inflateEnsure that the air line tubing is inserted into the air fittings as far as possible. The tubing s

Page 3 - Figure "D"

7FIRESTONE LIMITED LIFETIME AIR SPRING WARRANTYFirestone Industrial Products Company LLC (“Firestone”) warrants that its Ride Rite Air Spring Assembly

Page 4 - NOTE:

Page 5 - Trouble Shooting Guide

NOTE: Both illustrations are of the right, orpassenger’s,side of the vehicle. Reverse anyorientations when assembling and installingthe left, or drive

Page 6

PASSENGER’S SIDEAIR LINEPUSH-TO-CONNECTINFLATION VALVEFLAT WASHERHEX NUTVALVE CAPBODY OFVEHICLEFigure "B"STEP 1 - PREPARE THE VEHICLEWith th

Page 7

STEP 6 - INSTALLATION OF THE RIGHT SIDE ASSEMBLYFollow steps 1-5, reversing all orientations, for assembly and installation of the driver’s side assem

Page 8 - ONLINE AUCTION PURCHASES

Operating Instructions and Trouble Shooting Guide21-1083 4-12 Thank you for purchasing Firestone air helper springs. You have purchased a quality prod

Page 9 - AIR SPRING TECHNICAL DATA

2SAFETY TIPSNever exceed the manufacturer’s recommended Gross Vehicle Weight Rating (GVWR)As with your vehicle’s tires, an air helper spring is a pneu

Page 10 - IMPORTANT

3the suspension system. As more air pressure is added to the air springs, they will support more weight. You will be able to compensate for a heavy lo

Page 11

4INFLATING THE AIR SPRINGSWith the air helper springs installed on your vehicle and the vehicle sitting on a level surface, visually verify that the v

Page 12 - Air Command™

5Description Style Ride Height“X”Min/Max AirPressureMax Load @100 psi(per pair)6868 Single Convoluted 160BY 5.0" - 6.0" 5 / 100 psi 3600 lbs

Commentaires sur ces manuels

Pas de commentaire

Rite-ride 2378 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Rite-ride 2378. Rite-Ride 2378 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Rite-ride 2378