Rite-ride 2398 Manuel d'utilisateur télécharger pdf

2398

21-8317 05-07 NAD-34898-5

INSTALLATION INSTRUCTIONS

Congratulations - your new Air Helper Springs are quality

products capable of improving the handling and comfort of

your vehicle. As with all products, proper installation is the

key to obtaining all of the benefits your kit is capable of

delivering. Please take a few minutes to read through the

instructions to identify the components and learn where

and how they are used. It is a good idea to start by comparing

the parts in your kit with the parts list below.

The heart of the air helper spring kit is, of course, the air

springs. Remember that the air helper springs must flex and

expand during operation, so be sure that there is enough

clearance to do so without rubbing against any other part of the

vehicle.

Be sure to take all applicable safety precautions during the

installation of the kit. The instructions listed in this brochure

and the illustrations all show the left, or driver’s side of the

vehicle. To install the right side assembly simply follow the

same procedures.

Your kit includes separate inflation valves and air lines for

each air helper spring. This will allow you to level your vehicle

from side to side as well as from front to back. If you would

rather have a single valve inflation system, your dealer can

supply the optional "T" fitting.

IMPORTANT!

For your safety and to prevent possible damage to your

vehicle, do not exceed the maximum load recommended by

the vehicle manufacturer (GVWR). Although your Air Helper

Springs are rated at a maximum inflation pressure of 100

psi, this pressure may allow you to carry too great a load on

some vehicles. It is best to have your vehicle weighed once

it is completely loaded and compare that weight to the

maximum allowed. Check your vehicle owner’s manual or

data plate on driver's side door for maximum loads listed

for your vehicle.

When inflating your Air Helper Springs, add air pressure

in small quantities, checking pressure frequently during

inflation. The air spring requires much less air volume

than a tire and, therefore, inflates much quicker.

Remove the negative battery cable. It is not necessary to

jack up the truck to install this Ride-Rite kit, if you DO,

please use chocks in front of the front tires. Also, use jack

stands beneath the truck's rear axle that are properly rated to

support the trucks weight.

WARNING:

Do not inflate this assembly when it is unrestricted.

The assembly must be restricted by the suspension or

other adequate structure. Do not inflate beyond 100 psi

Improper use or over inflation may cause property damage

or severe personal injury.

224C AIR SPRING 6401 2

UPPER BRACKET 5462 2

LOWER BRACKET 5501 2

BRACKET CLAMP 5181 2

1/2" SPACER 5477 2

FUEL LINE BRACKET 5428 1

BAIL CLAMP 3077 2

AIR LINE TUBING 1

5/16" - 24 X 3/4" HEX HEAD BOLT 1

5/16" - 24 FLANGE NUT 1

5/16" FLAT WASHER 4

3/8"-16 X 8" CARRIAGE BOLT 4

3/8"-16 X 3/4" HEX HEAD BOLT 2

3/8"-16 X 2 1/2" FLAT HEAD BOLT 2

3/8"-16 FLANGE LOCK NUT 10

3/8" LARGE FLAT WASHER 2

3/4"-16 X 3" HEX BOLT 2

3/4"-16 HEX HEAD NUT 4

3/4" INTERNAL TOOTH LOCK WASHER 2

3/4" LOCK WASHER 2

3/4" LARGE FLAT WASHER 8

HEAT SHIELD 1004 1

INFLATION VALVE 3032 2

STRAIGHT FITTING 3046 2

THERMAL SLEEVE 2

NYLON TIE 6

CAUTION TAG 2

PARTS LIST

The air springs in this kit have a minimum

pressure of 5 psi and maximum of 100 psi after

the truck is loaded.

2WD ONLY

This kit does not require drilling into the frame.

1 2 3 4 5 6 ... 12 13

Résumé du contenu

Page 1 - 2WD ONLY

239821-8317 05-07 NAD-34898-5INSTALLATION INSTRUCTIONSCongratulations - your new Air Helper Springs are qualityproducts capable of improving the hand

Page 2 - FIGURE "A"

5Description Style Ride Height“X”Min/Max AirPressureMax Load @100 psi(per pair)6868 Single Convoluted 160BY 5.0" - 6.0" 5 / 100 psi 3600 lbs

Page 3 - STEP 1 - PREPARE THE VEHICLE

6TROUBLE SHOOTING GUIDEAir spring will not inflateEnsure that the air line tubing is inserted into the air fittings as far as possible. The tubing s

Page 4 - MAX PRESSURE (LOADED) 100 PSI

7FIRESTONE LIMITED LIFETIME AIR SPRING WARRANTYFirestone Industrial Products Company LLC (“Firestone”) warrants that its Ride Rite Air Spring Assembly

Page 5 - COMBO STUD NOTICE:

Page 6 - Trouble Shooting Guide

8 FIGURE "A"

Page 7

STEP 1 - PREPARE THE VEHICLEOn 2005 and newer vehicles some lines must be repositioned onthe left side of the vehicle. Remove the nut holding the fuel

Page 8

STEP 6 - CHECK THE SYSTEMFinal inspection. Visually check for loose attaching bolts. Make sure that no part of the truck is rubbingagainst the air spr

Page 9 - ONLINE AUCTION PURCHASES

ALIGNMENTPINCOMBO STUD NOTICE:THE ALIGNMENT PIN ON THE AIR SPRING MUST BE INSTALLEDINTO THE HOLE IN THE UPPER BRACKET.FAILURE TO DO SO WILL CAUSE THE

Page 10 - AIR SPRING TECHNICAL DATA

Operating Instructions and Trouble Shooting Guide21-1083 4-12 Thank you for purchasing Firestone air helper springs. You have purchased a quality prod

Page 11 - IMPORTANT

2SAFETY TIPSNever exceed the manufacturer’s recommended Gross Vehicle Weight Rating (GVWR)As with your vehicle’s tires, an air helper spring is a pneu

Page 12 - WARRANTY QUESTIONS

3the suspension system. As more air pressure is added to the air springs, they will support more weight. You will be able to compensate for a heavy lo

Page 13 - STEP #3:

4INFLATING THE AIR SPRINGSWith the air helper springs installed on your vehicle and the vehicle sitting on a level surface, visually verify that the v

Commentaires sur ces manuels

Pas de commentaire

Rite-ride 2398 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Rite-ride 2398. Rite-Ride 2398 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Rite-ride 2398